2013 Buick Regal Owners Manual

in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

12. Turn the ignition to LOCK/OFF

or press STOP to turn the ignition off.

13. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (55,1)

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule on page 11‑3. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the

rotation, check the wheel alignment. See When It Is Time for New Tires on page 10‑56
and Wheel Replacement on page 10‑61.

Use this rotation pattern when rotating the tires. Do not include the compact spare tire in the tire rotation.

Vehicle Care

10-55

Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10‑48
and Vehicle Load Limits on page 9‑10. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑51. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (56,1)

10-56

Vehicle Care

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10‑54 and Tire Rotation on page 10‑55.

The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The tire manufacturer date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (57,1)

slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating.

GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by MS for mud and snow. See Tire Sidewall Labeling on page 10‑43. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time.

Vehicle Care

10-57

If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation on page 10‑55 for information on proper tire rotation. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. Never exceed the winter tire's maximum speed capability when using winter tires with a lower speed rating.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (58,1)

10-58

Vehicle Care

{ WARNING

{ WARNING

Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.

{ WARNING

Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels.

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System on page 10‑50.

The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9‑10.

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (59,1)

{ WARNING

If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires on page 10‑57 and Accessories and Modifications on page 10‑3.

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with

Vehicle Care

10-59

nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (60,1)

10-60

Vehicle Care

graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on

straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of

performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other. If the vehicle vibrates when driving on a smooth

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (61,1)

{ WARNING

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.

road, the tires and wheels might need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

Vehicle Care

10-61

Used Replacement Wheels

{ WARNING

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Tire Chains

{ WARNING

Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle

(Continued)

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (62,1)

10-62

Vehicle Care

WARNING (Continued)

parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slow and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the front tires.

If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. See Tires on page 10‑41. If air goes out of a tire, it is much more likely to leak out slowly. But if there is ever a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

{ WARNING

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

{ WARNING

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for (Continued)

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (63,1)

Vehicle Care

10-63

Then see Tire Changing on page 10‑79. To use the tire sealant and compressor kit, see Tire Sealant and Compressor Kit on page 10‑64 or Tire Sealant and Compressor Kit on page 10‑71. When the vehicle has a flat tire (2), use the following example as a guide to assist you in the placement of wheel blocks (1).

WARNING (Continued)

WARNING (Continued)

1. Set the parking brake firmly. 2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. Turn off the engine and do not restart while the vehicle is raised.

4. Do not allow passengers to

remain in the vehicle.

5. Place wheel blocks on both

sides of the tire at the opposite corner of the tire being changed.

changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3.

{ WARNING

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

(Continued)

This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below.

1. Wheel Block 2. Flat Tire The following information explains how to repair or change a tire.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (64,1)

10-64

Vehicle Care

Tire Sealant and Compressor Kit

System Identification

If the vehicle has the tire sealant and compressor kit shown above, see the operating instructions that follow.

If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under "Tire Sealant and Compressor Kit (With Pressure Deflation Button).”

{ WARNING

Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO)

(Continued)

WARNING (Continued)

which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9‑26.

{ WARNING

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (65,1)

{ WARNING Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

If this vehicle has a tire sealant and compressor kit, there may not be a spare tire and tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire.

If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. Read and follow all of the tire sealant and compressor kit instructions. The kit includes:

1. On/Off Button

Vehicle Care

10-65

2. Selector Switch (Sealant/Air or

Air Only)

3. Pressure Relief Button 4. Pressure Gauge 5. Air Only Hose (Black) 6. Sealant/Air Hose (Clear) 7. Power Plug Tire Sealant Read and follow the safe handling instructions on the label adhered to the compressor. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” later in this section. There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (66,1)

10-66

Vehicle Care

“Removal and Installation of the Sealant Canister” later in this section. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.

heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3. See If a Tire Goes Flat on page 10‑62 for other important safety warnings. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑78.

2. Unwrap the sealant/air hose (6)

and the power plug (7).

3. Place the kit on the ground.

4. Remove the valve stem cap from

the flat tire by turning it counterclockwise.

5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.

6. Plug the power plug (7) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑6. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

When using the tire sealant and compressor kit during cold temperatures, warm the kit in a

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

8. Turn the selector switch (2)

clockwise to the Sealant + Air position.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (67,1)

9. Press the on/off button (1) to

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (4) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.

Inflate the tire to the recommended inflation pressure using the pressure gauge (4). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑48.

10.

The pressure gauge (4) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11.

Vehicle Care

10-67

11. Press the on/off button (1) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (7) from

the accessory power outlet in the vehicle.

13. Turn the sealant/air hose (6)

counterclockwise to remove it from the tire valve stem.

14. Replace the tire valve

stem cap.

15. Return the sealant/air hose (6) and the power plug (7) back in their original locations.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (68,1)

10-68

Vehicle Care

16.

If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

17. Return the equipment to its

18.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

19. Stop at a safe location and

20. Wipe off any sealant from the

wheel, tire, and vehicle.

21. Dispose of the used sealant canister and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.

22. Replace it with a new canister

available from your dealer.

23. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within 161 km (100 mi) of driving to have the tire repaired or replaced.

check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, use the compressor kit to inflate the tire to the recommended inflation pressure.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (69,1)

1. Remove the tire sealant and

6. Plug the power plug (7) into the

Vehicle Care

10-69

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑78.

2. Unwrap the air only hose (5) and

the power plug (7).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the tire valve stem cap

from the flat tire by turning it counterclockwise.

5. Attach the air only hose (5) onto

the tire valve stem by turning it clockwise until it is tight.

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑6. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

8. Turn the selector switch (2)

counterclockwise to the Air Only position.

9. Press the on/off button (1) to

turn the compressor on. The compressor will inflate the tire with air only.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3. See If a Tire Goes Flat on page 10‑62 for other important safety warnings.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (70,1)

10-70

Vehicle Care

10.

Inflate the tire to the recommended inflation pressure using the pressure gauge (4). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑48. The pressure gauge (4) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached. If the tire is inflated higher than the recommended pressure, press the pressure relief button (3), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (5).

11. Press the on/off button (1) to

turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (7) from

the accessory power outlet in the vehicle.

13. Disconnect the air only

hose (5) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap.

14. Return the air only hose (5)

and the power plug (7) back to their original locations.

15. Return the equipment to its

original storage location in the vehicle.

Removal and Installation of the Sealant Canister To remove the sealant canister:

1. Remove the plastic cover. 2. Unscrew the connector (2) from

the canister (1).

3. Pull up on the canister (1) to

remove it.

4. Replace with a new canister which is available from your dealer.

5. Push the new canister into

place.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (71,1)

6. Screw the connector (2) to the

canister (1).

7. Slide the plastic cover back on.

Tire Sealant and Compressor Kit

System Identification

If the vehicle has the tire sealant and compressor kit shown above, see the operating instructions that follow.

If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under "Tire Sealant and Compressor Kit (With Pressure Relief Button).”

{ WARNING

Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO)

(Continued)

Vehicle Care

10-71

WARNING (Continued)

which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9‑26.

{ WARNING

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (72,1)

The kit includes:

10-72

Vehicle Care

{ WARNING Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

If this vehicle has a tire sealant and compressor kit, there may not be a spare tire and tire changing equipment, and on some vehicles there may not be a place to store a tire.

The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. Read and follow all of the tire sealant and compressor kit instructions.

1. Selector Switch (Sealant/Air or

Air Only)

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (73,1)

Vehicle Care

10-73

There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.

2. On/Off Button 3. Pressure Gauge 4. Pressure Deflation Button

(If equipped)

5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under

Sealant/Air Hose)

Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following.

When using the tire sealant and compressor kit during cold temperatures, warm the kit in a

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (74,1)

10-74

Vehicle Care

heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3. See If a Tire Goes Flat on page 10‑62 for other important safety warnings. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑78.

2. Unwrap the sealant/air hose (6)

and the power plug (8).

3. Place the kit on the ground.

4. Remove the valve stem cap from

9. Press the on/off button (2) to

the flat tire by turning it counterclockwise.

5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.

6. Plug the power plug (8) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑6. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (3) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.

Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑48.

10.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

8. Press and turn the selector

switch (1) counterclockwise to the Sealant + Air position.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (75,1)

The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11.

11. Press the on/off button (2) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (8) from

the accessory power outlet in the vehicle.

13. Turn the sealant/air hose (6)

counterclockwise to remove it from the tire valve stem.

14. Replace the tire valve

stem cap.

15. Replace the sealant/air hose

(6), and the power plug (8) back in their original location.

Vehicle Care

10-75

16.

If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the tire sealant canister (5) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

17. Return the equipment to its

18.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (76,1)

10-76

Vehicle Care

19. Stop at a safe location and

check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.

20. Wipe off any sealant from the

wheel, tire, and vehicle.

21. Dispose of the used tire sealant canister (5) and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.

22. Replace it with a new canister

available from your dealer.

23. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within a 161 km (100 mi) of driving to have the tire repaired or replaced.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (77,1)

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑3. See If a Tire Goes Flat on page 10‑62 for other important safety warnings. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑78.

2. Unwrap the air only hose (7) and

the power plug (8).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the tire valve stem cap

from the flat tire by turning it counterclockwise.

5. Attach the air only hose (7) onto

the tire valve stem by turning it clockwise until it is tight.

6. Plug the power plug (8) into the

10.

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑6. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

8. Press and turn the selector

switch (1) clockwise to the Air Only position.

9. Press the on/off button (2) to

turn the compressor on. The compressor will inflate the tire with air only.

Vehicle Care

10-77

Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑48. The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached. If you inflate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deflation button (4), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (7).

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (78,1)

10-78

Vehicle Care

11. Press the on/off button (2) to

turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (8) from

the accessory power outlet in the vehicle.

13. Disconnect the air only hose

(7) from the tire valve stem by turning it counterclockwise, and replace the tire valve stem cap.

14. Replace the air only hose (7)

and the power plug (8) and cord back in their original locations.

15. Place the equipment in the

original storage location in the vehicle.

Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release

button (9).

3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer.

5. Push the new canister into

place.

Storing the Tire Sealant and Compressor Kit To access the tire sealant and compressor kit: 1. Open the trunk. See Trunk on

page 2‑11.

2. Lift the cover.

The tire sealant and compressor kit has an accessory adapter in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (79,1)

Vehicle Care

10-79

4. Wrench (In Bag) 5. Trim Removal (If Equipped) 6. Fastener (If Equipped) To access the spare tire and tools: 1. Open the trunk. 2. Remove the spare tire cover.

3. Turn the wing nut

counterclockwise to remove it.

4. Remove the tire sealant and

compressor kit.

To store the tire sealant and compressor kit, reverse the steps.

Tire Changing

Removing the Spare Tire and Tools

With Pressure Relief Button

With Pressure Deflation Button

1. Screwdriver 2. Tow Hook (If Equipped) 3. Jack

3. Turn the retainer nut

counterclockwise and remove the spare tire. Place the spare tire next to the tire being changed.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (80,1)

10-80

Vehicle Care

4. The jack and tools are stored below the spare tire. Remove them from their container and place them near the tire being changed.

Removing the Flat Tire and Installing the Spare Tire

2. Turn the wheel wrench

counterclockwise to loosen and remove the wheel nut caps. Do not try to remove plastic caps from the cover or center cap.

3. Pull the cover or center cap

away from the wheel. Store the wheel cover in the cargo area until you have the flat tire repaired or replaced.

Take off the wheel cover or center cap, if the vehicle has one, to reach the wheel bolts. 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10‑62.

4. Turn the wheel wrench

counterclockwise to loosen all the wheel nuts, but do not remove them yet.

5. Place the jack near the flat tire. 6. Put the compact spare tire

near you.

{ WARNING

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

{ WARNING

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (81,1)

Vehicle Care

10-81

{ WARNING

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

7. Attach the jack lift assist tool to the jack by fitting both ends of the jack and tool over one another.

8. Place the jack under the vehicle. Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

9. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a mark near the bottom edge of the lower molding. The jack must not be used in any other position.

10. Raise the vehicle by turning the

jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (82,1)

10-82

Vehicle Care

WARNING (Continued)

{ WARNING

an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

11. Remove all of the wheel nuts. 12. Remove the flat tire. { WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In

(Continued)

13. Remove any rust or dirt from

the wheel bolts, mounting surfaces, and spare wheel.

14. Place the compact spare tire

on the wheel-mounting surface.

15. Reinstall the wheel nuts.

Tighten each nut by hand until the wheel is held against the hub.

16. Lower the vehicle by turning

the jack handle counterclockwise.

{ WARNING

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the

(Continued)

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (83,1)

WARNING (Continued)

aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12‑2 for original equipment wheel nut torque specifications.

Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 12‑2 for the wheel nut torque specification.

Vehicle Care

10-83

Notice: Wheel covers will not fit on the vehicle's compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged. Storing a Flat or Spare Tire and Tools

{ WARNING

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

Store the spare or flat tire in one of the ways shown below. Storage instructions will vary depending on the bolt that came with the vehicle and how it attaches to the vehicle. This vehicle will have a slide in fastener or a screw in fastener.

17. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

18. Lower the jack all the way and remove the jack from under the vehicle.

19. Tighten the wheel nuts firmly

with the wheel wrench.

When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with the wheel wrench an additional one-quarter of a turn.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (84,1)

10-84

Vehicle Care

Storing a Flat or Spare Tire and Tools With a Screw in Fastener

6. Place the floor cover on the

4. Place the tire, lying flat, facing

wheel.

Storing a Flat or Spare Tire and Tools With a Slide In Fastener 1.

If the flat tire is larger than the spare tire, use the longer mounting bolt from the tool bag.

up in the spare tire well.

5. Turn the retainer nut clockwise

to secure the tire.

6. Place the floor cover on the

wheel.

To store the compact spare tire, use the shorter mounting bolt. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.

Compact Spare Tire { WARNING Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

1. Turn the wrench

counterclockwise to remove the fastener.

2. Replace the fastener with the

one provided in the foam.

3. Turn the wrench clockwise to

tighten the fastener.

4. Replace the foam, jack and

tools, and the tire.

5. Turn the retainer nut clockwise

to secure the tire.

2. Slide the shorter bolt to remove

it from the floor and insert the longer one.

3. Replace the jack and tools in their original storage location.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (85,1)

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi). Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h (50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area.

Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle. Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. Notice: Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.

Vehicle Care

10-85

Jump Starting

Jump Starting (On-board with eAssist Only) If the vehicle fails to crank, it may be jump started by using the eAssist battery to charge the 12-volt battery. Use the following procedure to activate the on-board jump start using the DIC controls.

DIC Buttons

1. SET/CLR 2. w / x (Thumbwheel) 3. MENU The vehicle may be equipped with an ignition key or an electronic keyless ignition with pushbutton start.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (86,1)

10-86

Vehicle Care

Key Access Place the ignition key in the ON/ RUN position and proceed as follows: 1. Press MENU (3) on the turn

signal lever until Vehicle Information Menu is displayed. Use w / x (Thumbwheel) (2) to scroll through the menu items until Jump Start is displayed.

2. Press SET/CLR (1) to activate

the jump start.

3. The system will then ask for

confirmation. If yes is selected, the jump start will begin and the display will show JUMP START ACTIVE WAIT TO START.

4. When the jump start is complete,

the display will show JUMP START COMPLETE ATTEMPT START.

Keyless Access With the brake pedal not applied, press and hold the ENGINE START/ STOP button for more than five seconds. This will place the vehicle in the Service Only Mode. Proceed as follows: 1. Press MENU (3) on the turn

signal lever until Vehicle Information Menu is displayed. Use w / x (Thumbwheel) (2) to scroll through the menu items until Jump Start is displayed.

2. Press SET/CLR (1) to activate

the jump start.

3. The system will then ask for

confirmation. If yes is selected, the jump start will begin and the display will show JUMP START ACTIVE WAIT TO START.

4. When the jump start is complete,

the display will show JUMP START COMPLETE ATTEMPT START.

If the vehicle is started, the on-board jump start function will be automatically disabled. If the vehicle cranks but does not start, the procedure may be repeated again. If the vehicle start is still unsuccessful, the jump start can be attempted using the following jump starting procedure under “Jump Starting (with or without eAssist).” On-board jump starting may be unavailable due to the 12-volt battery charge level, the eAssist battery charge level, power capability, or an issue with the eAssist system. In these cases, the display will not be available because of the power issue, or the DIC will display JUMP START DISABLED SEE OWNERS MANUAL.

Buick Regal Owner Manual - 2013 - crc - 11/5/12

Black plate (87,1)

Jump Starting (with or without eAssist) For more information about the vehicle battery, see Battery on page 10‑26. If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ WARNING

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

2.0L Engine Shown, 2.4L Engines

Similar

The jump start positive is under a trim cover in the engine compartment on the driver side of the vehicle.