Download PDF Manual


CONTINUED 113


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


Door/Window Setup Here are the five custom settings for the door/window setup: ● AUTO DOOR LOCK ● AUTO DOOR UNLOCK ● KEY AND REMOTE UNLOCK


MODE


● KEYLESS LOCK


ACKNOWLEDGMENT


● SECURITY RELOCK TIMER While ‘‘DOOR/WINDOW SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.


114


SEL/RESET BUTTON INFO (▲or▼) BUTTON


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


AutoDoorLock There are three settings you can choose from: SHIFT FROM P - The doors lock whenever you move the shift lever out of Park. WITH VEH SPD - The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h). OFF - The auto door lock is deactivated all the time.


You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.


Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.


CONTINUED 115


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


AutoDoorUnlock There are three settings you can choose from: SHIFT TO P - The driver's door or all the doors, depending on the door lock mode setting (see page 115), unlock when you move the shift lever to Park with the brake pedal depressed. IGN OFF - The driver's door or all the doors, depending on the door lock mode setting (see page 115), unlock when you turn the ignition switch to the LOCK (0) position. OFF - The auto door unlock is deactivated all the time. This is the factory default setting.


You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.


116


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.


If you choose ‘‘SHIFT TO P’’ or ‘‘IGN OFF’’, you will see the above display. Press the INFO ( / ) button to switch the door lock mode setting between the driver's door and all doors. Then, press the SEL/RESET button to enter your selection.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.


CONTINUED 117


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


KeyandRemoteUnlockMode


Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again.


To select whether the driver's door unlocks or all the doors unlock when you unlock the doors with the remote transmitter, follow these instructions. You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.


118


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the tailgate are locked and the security system has set (see page 337). You can customize the exterior lights not to flash and the beeper not to sound.


You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.


Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.


CONTINUED 119


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


SecurityRelockTimer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets. You can change this relock time from 30 seconds to 60 or 90 seconds.


You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.


120


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.


CONTINUED 121


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


Wiper Setup


SEL/RESET BUTTON INFO (▲/▼) BUTTON


Here is one custom setting for the wiper setup: ● WIPER ACTION While ‘‘WIPER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.


Each time you press the INFO ( / ) button, the screen changes as shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.


122


WiperAction You can select from these two settings when the wiper switch is in the INT (intermittent) position: INTERMITTENT - The intermittent operation varies according to the selection you make on the wiper lever's intermittent control ring. WITH VEH SPD - The intermittent operation varies according to vehicle speed.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Multi-Information Display


You can choose this customize item from ‘‘WIPER SETUP’’ by pressing the INFO ( / ) button repeatedly.


Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.


When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘WIPER ACTION’’ and repeat the procedure again.


123


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Controls Near the Steering Wheel


BSI ALERT INDICATORꭧ1
(P. 473)


COLLISION MITIGATION BRAKING SYSTEM™ (CMBS™) OFF BUTTONꭧ1 (P. 461) VEHICLE STABILITY ASSIST SYSTEM OFF SWITCH (P. 468) MIRROR CONTROLS (P. 164) HEADLIGHT WASHER SWITCHꭧ1 (P. 126) BLIND SPOT INFORMATION SYSTEM (BSI) OFF BUTTONꭧ1
(P. 476)


STEERING WHEEL AUDIO CONTROLS (P. 302) STEERING WHEEL ADJUSTMENTS (P. 133)


HEADLIGHT/TURN SIGNAL/ FRONT FOG LIGHTS (P. 127)


PADDLE SHIFTERS (P. 441)


WINDSHIELD WIPERS/WASHERS (P. 125)


HORNꭧ2


VOICE CONTROL BUTTONSꭧ3


DISTANCE BUTTONꭧ1
(P. 354)


BLUETOOTH HANDSFREELINK BUTTON (P. 363)


CRUISE CONTROL BUTTONS (P. 342)/ ADAPTIVE CRUISE CONTROL (ACC) BUTTONSꭧ1 (P. 350)


INSTRUMENT PANEL BRIGHTNESS (P. 132) PASSENGER AIRBAG OFF INDICATOR (P. 36) HAZARD WARNING BUTTON (P. 131) REAR WINDOW DEFOGGER (P. 131) ACCESSORY POWER SOCKETS (P. 175)


SEAT HEATER SWITCHES (P. 156)/ SEAT HEATER AND SEAT VENTILATION BUTTONSꭧ1
(P. 157) ACTIVE DAMPER SYSTEM SWITCHꭧ1
(P. 478)


ꭧ1: If equipped ꭧ2: To use the horn, press the center pad of the steering wheel. ꭧ3: Refer to the navigation system manual. For how to operate Bluetooth®HandsFreeLink by voice, see page 380.


124


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Windshield Wipers and Washers


Push the right lever up or down to select a position. MIST - The wipers run at high speed until you release the lever. OFF - The wipers are not activated. INT - The length of the wipe interval is varied automatically according to vehicle speed. Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h). To change the ‘‘WIPER ACTION’’ setting, see page 122.


position), the


LO - The wipers run at low speed. HI - The wipers run at high speed. Windshield Washer - Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever. When you activate the windshield washer with the headlights turned on, the headlight washer will be activated under certain conditions. For more information, see following HeadlightWasherssection.


1. MIST 2. OFF 3. INT - Intermittent 4. LO - Low speed 5. HI - High speed 6. Windshield washers


CONTINUED 125


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Windshield Wipers and Washers


HeadlightWashers (OnCanadianmodels)


The headlight washers use the same fluid reservoir as the windshield washers.


Rear Window Wiper and Washer


The headlight washers can be operated at any time by pressing the headlight washer button located next to the steering wheel column. The headlights must be turned on to use this button. In addition, the headlight washer operates without pressing the button the first time you turn on the windshield washers with the ignition switch in the ON (II) position.


126


1. Rotate the switch clockwise to turn


the rear window wiper ON.


2. Hold past ON to turn the rear


window wiper on and to spray the rear window washer.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Windshield Wipers and Washers, Turn Signal and Headlights


3. When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position.


4. Rotate the switch


counterclockwise to spray the window washer. When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically. When the wiper control lever position is INT, the rear wiper operates intermittently. When it is LO or HI, the rear wiper operates continuously.


The rear window washer uses the same fluid reservoir as the windshield washer.


Turn Signal and Headlights


1. Turn signal 2. Off 3. Parking and indicator lights 4. AUTO 5. Headlights on 6. High beams 7. Flash high beams 8. Fog lights off 9. Fog lights on


Turn Signal - Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn. Headlights On - Turning the switch to the ‘‘ the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the ‘‘ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver's door.


’’ position turns on


’’


CONTINUED 127


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Turn Signal and Headlights


When the light switch is in either of these positions, the lights on indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position. High Beams - To switch from low beams to high beams, push the left lever forward until you hear a click. The blue high beam indicator will come on (see page 72). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams stay on as long as you hold the lever back.


128


Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities. To change the ‘‘AUTO LIGHT SENSITIVITY’’ setting, see page 112. Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.


AUTO - The automatic lighting feature turns on the headlights and all other exterior lights, when it senses low ambient light. To turn on automatic lighting, turn the light switch to AUTO at any time. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light. The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver's door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the


position.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


LIGHT SENSOR


The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.


Turn Signal and Headlights


Fog Lights Turn the fog lights on and off by turning the switch next to the headlight switch. You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position, you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off.


Daytime Running Lights With the headlight switch off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. When the headlights are on, the daytime running lights are off.


CONTINUED 129


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Automatic Lighting Off Feature This feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15
seconds after you remove the key and close the driver's door. To change the ‘‘HEADLIGHT AUTO OFF TIMER’’ setting, see page 111. The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position, and you remove the key, then open and close the driver's door.


’’ or ‘‘


’’


If you turn the ignition switch to the LOCK (0) position with the headlight switch on, but do not open the door and get out, the lights turn off after 10 minutes (3 minutes, if the switch is in the ‘‘AUTO’’ position). The lights turn on again when you unlock or open the driver's door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver's door open, you will hear a lights-on reminder chime.


Turn Signal and Headlights


If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi-information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked. When the multi-information display shows a ‘‘DRL OFF’’ message, the daytime running lights are off. Follow the procedure in the left column to turn them on.


130


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Hazard Warning Button, Rear Window Defogger


Hazard Warning Button


Rear Window Defogger


Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.


The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.


Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. Pushing this button also turns the mirror heaters on or off. For more information, see page 165.


131


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Instrument Panel Brightness


Adjust the brightness of the instrument panel by pressing the + or - button. Press the + button to increase the brightness and the - button to decrease it. The brightness can be set differently for when the headlights are on, and when they are off.


The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.


132


. To cancel the glare reduction


To reduce glare at night, the instrument panel illumination dims when you turn the light switch to or function, set the brightness to the highest level, then press the + button. You will hear a beep when it is canceled. You can customize when the glare reduction function starts. To change ‘‘AUTO INTERIOR ILLUMINATION’’, see page 104 for more information.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Make any steering wheel adjustment before you start driving.


ADJUSTMENT SWITCH


Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.


Adjust the steering wheel only when the vehicle is stopped.


Move the steering wheel in, out, up, or down by pushing and holding the adjustment switch in that direction.


Steering Wheel Adjustments


Release the switch when the steering wheel reaches the desired position. Make sure the steering wheel points towards your chest, not toward your face, and that you can see the instrument panel gauges and indicators.


CONTINUED 133


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Steering Wheel Adjustments


When you remove the key from the ignition switch, the steering wheel automatically moves fully in and up. To change the ‘‘AUTO TILT & TELESCOPE STEERING WHEEL’’ setting, see page 108. The steering wheel then returns to its original position when you insert the key back in the ignition switch. Steering wheel movement is also controlled by the driving position memory system (see page 166).


If your vehicle's battery is disconnected or goes dead, or the fuse for the power tilt and telescopic steering wheel is removed, the power tilt and telescopic steering wheel system needs to be reset when you reconnect the battery or install the fuse. Insert the key into the ignition switch, and remove it. The steering wheel automatically moves fully in and up to let you know the system is reset.


134


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


KEY NUMBER TAG


MASTER KEY WITH REMOTE TRANSMITTER


VALET KEY (Light Gray)


You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks.


The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver's door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.


Keys and Locks


These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. ● Protect the keys from direct


sunlight, high temperature, and high humidity.


● Do not drop the keys or set heavy


objects on them.


● Keep the keys away from liquids.


If they get wet, dry them immediately with a soft cloth. The valet key does not contain a battery. Do not try to take it apart.


CONTINUED 135


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Always use the fully-extended key when you insert it to the ignition switch. If the key does not fully extend, the immobilizer system may not operate properly and may prevent the engine from starting.


The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending the key.


Keys and Locks


RetractableMasterKey


RELEASE BUTTON


Push


The master key can be retracted into the remote transmitter. To use the key, push the release button to release the key from the transmitter. The key should be fully extended. To retract the key, push the release button and at the same time push the key into the remote transmitter until it is securely latched.


136


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


The Immobilizer System protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again. The system may not recognize your key's coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.


If the system repeatedly does not recognize the coding of your key, contact your dealer. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable. If you have lost your key and you cannot start the engine, contact your dealer.


Always take the ignition key with you whenever you leave the vehicle alone.


Immobilizer System


AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.


137


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Ignition Switch


ACCESSORY (I) - You can operate the audio system and the accessory power sockets in this position. ON (II) - This is the normal key position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position. START (III) - Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the key.


You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper. The shift lever must be in Park before you can remove the key from the ignition switch.


The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) - You can insert or remove the key only in this position. To turn the key to the LOCK (0) position, the shift lever must be in Park, and you must push the key in slightly. If the front wheels are turned, the anti- theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.


138


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


UNLOCK


LOCK


LOCK


UNLOCK


To lock all doors and the tailgate, press the bottom of the master door lock switch on either front door, pull the lock tab above the driver's door handle, or use the key on the outside lock on the driver's door. Pressing the top of either master door lock switch will unlock all doors and the tailgate.


The lock tab on any passenger's door locks and unlocks that door. All doors and the tailgate can be locked from the outside by using the key in the driver's door lock. To unlock only the driver's door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds.


Door Locks


To change the ‘‘KEY AND REMOTE UNLOCK MODE’’ setting, see page 118. When the vehicle speed reaches about 10 mph (about 16 km/h) or more, all the doors lock automatically. To change the ‘‘AUTO DOOR LOCK’’ setting, see page 115. When you shift to P after driving, the driver's door unlocks. To change the ‘‘AUTO DOOR UNLOCK’’ setting, see page 116.


CONTINUED 139


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Door Locks, Tailgate


LockoutPrevention With any door and the tailgate open and the key in the ignition, both master door lock switches are disabled. They are not disabled if all the doors and the tailgate are closed. If you try to lock an open driver's door by pulling the lock tab rearward the lock tab on the driver's door pops out.


140


Childproof Door Locks


Tailgate


LOCK


The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.


To open the tailgate, push up inside the handle, then lift up. To close the tailgate, use the inner handle to pull it down, then press down on the back edge. Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 60.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Power Tailgate


If you push the same button or switch again while the tailgate is opening or closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened or closed position.


POWER TAILGATE SWITCH


The tailgate can be opened and closed with the remote transmitter (see page 144) or the switch in the driver's door pocket when both front doors are unlocked. Press and hold the tailgate button on the remote transmitter or the switch for about 1 second to open or close the tailgate. Each time you press the button on the remote transmitter or the switch, you will hear a beep, and some front and rear lights will flash.


Tailgate


TAILGATE SWITCH


The tailgate can also be closed by pressing the button on the tailgate. If you press the button again while the tailgate is closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened position.


CONTINUED 141


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Tailgate


Auto-Reverse The power tailgate has an auto- reverse feature. If it meets resistance while opening or closing, it will beep three times and reverse direction. However, the tailgate may not reverse immediately. Always make sure passengers and objects are clear of the tailgate before opening or closing it.


Closing a power tailgate while anyone is in the path of the tailgate can cause serious injury.


Make sure everyone is clear before closing the power tailgate.


142


Do not install any accessories on the tailgate. It may cause the tailgate to malfunction. If there is snow or ice on the tailgate, make sure to remove it before you operate the tailgate. If you push the tailgate release button inside the handle while the tailgate is opening or closing, it will stop moving. You need to open or close it the rest of the way manually. The tailgate has sensors on both sides. Be careful not to damage them. If the sensors are damaged, the power tailgate does not function properly.


Also check that passengers, especially children, do not have their hands on the edge of the tailgate or on the tailgate sill. The auto reverse feature stops working when the tailgate is about to latch so the motor can pull the tailgate shut. If your vehicle's battery is disconnected, goes dead, or the fuse is removed while the tailgate is fully open, the power tailgate needs to be reset. After connecting the battery or installing the fuse, close the tailgate fully by hand. The power tailgate may not open or close under the these conditions: ● The vehicle is parked on a steep


hill.


● When the vehicle is swayed in a


strong wind.


● When the tailgate or the roof is


covered with snow or ice.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Unlocking the Tailgate


Tailgate


If the power door lock system cannot unlock the tailgate, unlock it manually. Use a small flat-tipped screwdriver to remove the cover on the back of the tailgate.


Push the release lever to the right as shown. If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.


If you try to drive off with the tailgate not closed completely, a beeper sounds and a ‘‘DOOR & TAILGATE OPEN’’ message is shown on the multi-information display. Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 60. If there is a problem in the power tailgate system, you will see a ‘‘CHECK POWER TAILGATE’’ message on the multi-information display. Have the system checked by your dealer. With this message shown on the multi-information display, you can still open or close the tailgate manually.


143


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


UNLOCK - Press this button once to unlock the driver's door. Push it twice to unlock the other doors. Some exterior lights will flash twice when you push the button. If you do not open any door or the tailgate within 30 seconds, they will automatically relock. To change the ‘‘KEY AND REMOTE UNLOCK MODE’’ setting, see page 118. To change the ‘‘SECURITY RELOCK TIMER’’ setting, see page 120.


The door activated spotlights come on when you press the UNLOCK button if the door activated position is selected by pressing the light control button (DOOR). If you do not open any door within 30 seconds (or whatever setting of the interior light dimming time is set to), the lights will fade out. If you relock the doors with the remote transmitter before 30
seconds have elapsed, the lights will go off immediately. TAILGATE - Press and hold the TAILGATE button to open or close the power tailgate. When the tailgate begins to move, you will hear a beep, and some front and rear lights will flash.


Remote Transmitter


UNLOCK BUTTON


LOCK BUTTON


TAILGATE BUTTON


PANIC BUTTON LOCK - Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed. To change the ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ setting, see page 119.


144


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


If you push the same button again while the tailgate is opening or closing, three beeps sound, the tailgate stops moving, reverses direction and stops in the fully opened or fully closed position. PANIC - Press and hold this button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.


RemoteTransmitterCare ● Avoid dropping or throwing the


transmitter.


● Protect the transmitter from


extreme temperature.


● Do not immerse the transmitter in


any liquid.


● If you lose a transmitter, the


replacement needs to be reprogrammed by your dealer.


Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616


Remote Transmitter


SCREW


KEYPAD


To replace the battery: 1. Remove the screw at the base of


the transmitter with a small Phillips-head screwdriver. NOTE: Be careful when removing this screw as the head of the screw can strip out.


2. Separate the keypad from the


transmitter by pushing any button from outside.


CONTINUED 145


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Remote Transmitter


BATTERY


3. Place a cloth on the edge of the


keypad, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver.


146


4. Remove the old battery and note


the polarity. Make sure the polarity of the new battery is the same (- side facing up), then insert it in the keypad. An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.


5. Snap the two halves of the keypad,


then install the parts in reverse order.


AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Recalling a Memorized Driving Position


When you unlock the driver's door with your remote, each remote activates the keyless memory settings related to that remote. The driver's ID (DRIVER 1 or DRIVER 2) is shown on the back of each remote.


Here are the settings activated with the remote: ● Customized settings


(see page 89).


● Driving position memory


(see page 166).


● Audio system settings


(see page 209).


● Climate control settings


(see page 181).


When you unlock and open the driver's door with the remote transmitter, the driver's seat (except the power lumbar feature) and outside mirrors start to move to the positions stored in memory. The indicator in the related memory button to the remote comes on.


Remote Transmitter


The steering wheel will move to the stored position when you insert the key into the ignition switch. You will also see the ‘‘WELCOME DRIVER 1’’ or ‘‘WELCOME DRIVER 2’’ message on the multi-information display, depending on which linked remote transmitter is used.


147


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Seats


Front Seat Power Adjustments Seepages14-15forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. The controls for the power adjustable front seats are on the outside edge of each seat bottom. You can adjust the seats with the ignition switch in any position. Make all seat adjustments before you start driving. The passenger seat has the same adjustments as the driver's seat but without any lumbar adjustment.


148


Moves the seat forward and backward.


Moves the front of the seat up or down.


Raises or lowers the seat.


Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.


Adjusts the seat-back angle forward or backward.


Increases or decreases the lumbar support. (Driver's seat only)


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Head Restraints Seepage15forimportantsafety informationandawarningabout improperlypositioningheadrestraints. Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from the likelihood of whiplash and other injuries.


They are most effective when you adjust them so the center of the back of the occupant's head rests against the center of the restraint.


Seats


CUSHION


FRONT


SEAT- BACK


LEGS


RELEASE BUTTON


AdjustingtheHeadRestraint The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.


CONTINUED 149


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button. Make sure the head restraint locks in position when you reinstall it.


Failure to reinstall the head restraints can result in severe injury during a crash.


Always replace the head restraints before driving.


Seats


SECOND CENTER AND THIRD ROW CUSHION


LEGS


RELEASE BUTTON


RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat-back.


150


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Seats


This reduces the distance between the restraint and the occupant's head. It also helps protect the occupants against the likelihood of whiplash and injuries to the neck and upper spine. After a collision, the activated restraint should return to its normal position. If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by an Acura dealer.


For a head restraint system to work properly: ● Do not hang any items on the head


restraints, or from the restraint legs.


● Do not place any object between


an occupant and the seat-back.


● Install each restraint in its proper


location.


● Only use genuine Acura


replacement head restraints.


ActiveHeadRestraints


The driver's and front passenger's seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.


CONTINUED 151


2011 MDX Make sure that the folded seat-back does not press against the front passenger's seat, as this could cause the weight sensors to work improperly.


10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Seats


Adjusting the Second Row Seats


HANDLE


To change the seat-back angle of the seats in the second row, pull up on the handle on the outside of the seat- back, and push the seat-back. Overall, the seat-back has six different positions.


152


Folding the Second Row Seats The left and right halves can be folded separately. 1. To unlatch the detachable anchor before folding the seat-back, insert the latch plate into the slot on the side of the anchor buckle (see page 154) and allow the seat belt to retract. Store the detachable anchor and seat belt latch plates in the retractor housing.


2. Lower the head restraints to their


lowest positions.


3. Pull up the handle on the outside


of the seat-back.


4. Fold the seat-back forward. Reverse this procedure to return the seat to the upright position. Make sure the seat is locked securely before driving.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Third Row Access


Folding the Third Row Seat 1. Use the latch plate to release the


seat belt from the detachable anchor (see page 154).


2. Lower the head restraints to their


lowest positions.


NOTE: To fold the third row seat, the second row seat-back must be folded down or in the full up right position.


RELEASE LEVER


To get into the third row seats, pull up the lever on the side of the passenger's side second row seat- back. The seat-back will tilt forward, and then can be slid forward. After you return the seat-back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before sitting in it.


Seats


THIRD ROW SEAT


HANDLE 3. Unlock the seat-back by pulling the handle. Push the seat-back forward.


Make sure the outer shoulder belts are positioned on each hook on the side panel whenever the third seat is folded.


CONTINUED 153


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Seats


Reverse this procedure to return the seat to the upright position. Make sure the seat is locked securely before driving. Reconnect the seat belts to the detachable anchors. Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard (See Carrying Cargo on page 428).


Detachable Anchor


LATCH PLATE


The seat belts in the second row center seat and the third row seats are equipped with detachable anchors. To unlatch the detachable anchor, insert the latch plate into the slot on the side of the anchor buckle. Store the detachable anchor and seat belt latch plates in the retractor housing.


154


When the seats are returned to the upright position, these detachable anchors should be latched back properly.


Using the seat belt with the detachable anchor unlatched increases the chance of serious injury or death in a crash.


Before using the seat belt, make sure the detachable anchor is correctly latched.


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


SECOND ROW CENTER SEAT


THIRD ROW SEATS


SMALL LATCH PLATE


LATCH PLATE


Seats


HOOK


TRIANGLE MARKS


SMALL LATCH PLATE


Pull out the small latch plate and the latch plate from each holding slot in the ceiling, and pull out the seat belt to extend it.


Pull out the outer shoulder belts from the hook. Both of the third-row hooks should only be used when the seat belt is detached.


ANCHOR BUCKLE


Line up the triangle marks on the small latch plate and anchor buckle when reattaching the belt and buckle. Tug on the seat belt to verify that the detachable anchor is securely latched. Make sure the seat belt is not twisted.


155


2011 MDX 10/06/29 11:59:04


11 ACURA MDX MMC North America Owner's M 50 31STX640 enu


Seat Heaters


Passenger's Seat


HI

Loading...
x