Turbos And Lpg ?  

wiggywiggywildwildwest
  • wiggywiggywildwildwest
  • Standard User
  • Member No.: 54,464
  • Joined: 18-October 06
  • Posts: 224
Post #1 post 22nd October 2006 - 07:51 PM
hi there. i have a 2L escort which i have recently changed over to gas. i used an impco model l converter, and an impco 200 mixer. i would like to blow through this setup. anyone got any advice or experiences ?

--------------------
livin in the wiggy wiggy wild wild west
2_wheelin
Post #2

dont do blow through, it will not be worth your while as when the fuel and the air go in it mixes them un evenly and will never run as well as an injected setup, your a better off switchin to come kind of injected engine and then turboing it

wiggywiggywildwildwest
Post #3

i already have the gas setup on the car. i would like to blow through it. anyone ?

2_wheelin
Post #4

yeh u could still u most of the gas stuff u have now... u would just have to change the way it goes into the engine

wiggywiggywildwildwest
Post #5

i don't want to draw through. the turbo i have doesn't have a carbon seal in the inlet side. as well,draw through has its own set of issues.

RX4_guy
Post #6

Cant really help you with the escort motor, but their are quite a few Impco set ups on Rotarys which are blow-through and they do work well wink.gif

wiggywiggywildwildwest
Post #7

QUOTE(RX4_guy @ Oct 24 2006, 06:28 PM) [snapback]1280393749[/snapback]

Cant really help you with the escort motor, but their are quite a few Impco set ups on Rotarys which are blow-through and they do work well wink.gif


I'm sure the basics are the same. can you give me details of the setups ? or failing that, can you put me onto the people who built/tuned the setup ?

Sir_2jza70
Post #8

You will need a different carby that is design to work with a forced induction "blow through" setup, normally NA carbys have been known to bend throttle butterflys under boost as there is very low pressure on one side, and very high pressure on the other.

There will be more but I is no LPG expect.

Possibly have to look at what type of gas convertor youd be using as you need one with higher pressure to still be able to flow gas into a pressurised system.

stevez
Post #9

QUOTE(wiggywiggywildwildwest @ Oct 23 2006, 01:51 PM) [snapback]1280387611[/snapback]

hi there. i have a 2L escort which i have recently changed over to gas. i used an impco model l converter, and an impco 200 mixer. i would like to blow through this setup. anyone got any advice or experiences ?


I've had many gas powered turbo cars. I'm a certified lp gas fitter and have tried out most of the gas syetems out there. My recomendation is use the impco convertor you have and use a gas research lp gas carby on it. It will suplly more than enough gas and good tunability.

turbo_LTD
Post #10

naaaah. u can do it.
u can run the 200 in blow through, make sure you have a balance tube running from turbo outlet to converter. with a good tune, and nicely sized lpg feed tube, high flow lockoff, etc, u could make so good power.

my ltd is turbo'd, runs impco 225 with x1 ohg converter, and its still holding out at 8 psi.

wiggywiggywildwildwest
Post #11

did you set it up ? how do you go with tuning ? could i connect the balance pipe into the converter to the fiting on the turbo side of the mixer ? any help would be much appreciated.

turbogemi
Post #12

hey mate, i had a gemini motor (isuzu G161) with a blow through LPG turbo setup on it.

I suggest gas research throttle body over the impco, jump onto the gas research website they have a great deal of good information to download!

turbo_LTD
Post #13

make sure ur gas line is at least 5/16". any smaller and you'll starve of fuel.
are you running a cooler? if you are, plumb it up the usual way, with the mixer downstream. run the balance pipe (min 3/8") from converter lid to turbo-to-intercooler pipe.
as a starting point, set the cruise mixture to just under halfway, and richen the idle by a 1/4 turn. of course you must get the car on the dyno to verify.
you'd want to ensure your ignition system is perfect, so u dont get nasty backfires.

impco mixers are easier to setup and tune for lower boost applications than gas research. the only real benefit of gas research is that they ultimately can flow more, only useful for making big power.

  • Member Login

    If you have a BoostCruising account enter your user name and password into the yellow box.

    Alternatively, you can quickly login with Facebook.

    If you don't have an account create one below.

    Create Account
  • Login with Facebook

    Login using your Facebook account!

1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
Loading...
x