***MUST SELL ASAP** ...or Swap for a Black 6 litre manual Ve with similar K's..
460 hp .. (350 + kw) Twin turbo Ls1 Vx ss 2001, Silver in Colour.(mint paint) just hit 130 xxxks..
Cammed (232/243) ivan tighe roller Ls1 Twin turbo ( t3's with t'4 housing ) top mounts, Stainless headers &dumps into twin 3" X force out back. Minor engine pull down 3 weeks before Christmas 2016 (just to check out before turbos went on) and replace gaskets throughout. all parts listed below brand new. .less than 1000'ks since back together.
New : fuel hose, Rear main Crank seal, Sump gasket, front engine gasket, Stainless header gaskets, new oil pump, manifold studs. New parts: engine mounts, Aeroflow alloy weld on's (for turbo feed lines from sump) return lines (braided) ARP Cam bolt, Brand new Exeedy h/d Button clutch, Raceworks intank pump, Raceworks 1000' cc injectors, Raceworks 2 bar map sensor, Rollmaster double row chain, new oil supply / feed lines and Aeroflow fittings, Power block upfront (battery relocated) engine was full mafless tune before turbos went on. 6 speed T56 manual with brand new short shifter (race series) Brand new turbo kit fitted . (consists of) Custom Stainless steel headers X 2 T3/t4 hybrid V band turbos. t4 Compressor wheel & t3 type turbine flange. 0.57 compressor wheel trim 8psi internal wastegates. (capable of easy (capable of 600 easy) wet float bearings and properly balanced, 1/8 Npt oil inlet, 1" returs back to sump (all braid with Aeroflow fittings) mapped for Low & High boost setup (currently 6psi) 0.63 A/r turbine housing, new oil fittings, gaskets and mount studs. Huge front mount cooler- bar & plate design made from 6051 billit aluminum light weight material. Cnc machined & all tig welde, max psi is 35 or upto 650 hp. overall diameter: 32.5 inches X 11.75 inch high with 3 inch inlet. Core size: 24 inch X 11.75 inch& 3 inch inlet & outlet tubes. Cooler is huge and all behind front bumper (fog lights removed to clear piping but still have them here) Cooler painted black so not noticeable (stays cool as aswell ) piping is 6051 billit alloy material, Cnc machine mandrel bent 3 inch tube. running no blow off valve (been deleted for sensor plug) but have a brand new Rs style here, holds up to 650 hp or 25 psi boost pressure. Aeroflow braided -10an hose, Aeroflow stainless feed hoses with 550 series full flow fittings in oil drainlines. Aeroflow silicone hoses, Turbosmart boost lines, all correct brass turbo fittings. Turbos have beanies fitted (turbos painted 2 pack phantom black) All cooler piping and dumps clears factory items in car (steering etc) Brand new 60psi Turbosmart E-boost 2 boost controller fitted with Hks turbo timer 19" Xhp wheels, Lsd rear, t56 with short shifter, button clutch., car is lowered (kings spings fitted) Ecu relocated to glovebox...battery located in boot (battery box fastened) Exhaust heat wrapped from turbos to halfway under car (3" stainless) new 02 sensors. To much more to mention.... All brand new less than 1000k's.!! since fitted. Car has been Very safe tuned & dyno..made an easy 460hp ( 350kw)....960nm torque in 96.5% air density on 6psi boost in 4th gear. has way more init yet.. (its only my work car)...will make 500 with bit more boost easy. Tuned to 460atm so i could get use to it first..has a mad cam note to it (sounds tuff)....only use 98-100 octane.. Drives mint and Very good on fuel with the turbos onit...Hits boost hard straight away no problems at all, Sounds tough and quiet quick indeed.!!! Fully legal and all Legit ...all Qld Bluetagged... All work by EDGE Automotive and Performance... .Toowoomba have receipts for turbo work and parts here. (turbos and work alone was 9000 ) Garaged always & rego till mid march 17. has personal plates..51CSS...can supply dyno sheets. car in sweet condition overall. Very tidy allover and VERY Quick!! after another tuff car..sad to see go :/ Swap for a Black 6 litre manual Ve with similar K's. .Prefer Brisbane area. wanting $14500...but open to offers...**MUST SELL ASAP** phone : XXXX-XXX-XXX.. Toowoomba qld.
Detailed Specifications
general
Make
HOLDEN
Family
COMMODORE
Variant
SS
Series
VY
Engine
MULTI POINT F/INJ
CC
5665
Size
5.7L
Cylinders
V8
Country of Origin
AUSTRALIA
Fuel Type
UNLEADED PETROL
Vehicle Segment
LARGE
Fuel City (L/KM)
13.5
Fuel Highway (L/KM)
8.5
suspension
Track Front
1558
Track Rear
1576
Brake Front
DV
Brake Rear
DC
Tyre Front
235/40 R18
Tyre Rear
235/40 R18
Suspension Front
MacPherson strut, Stabiliser bar, Coil Spring.
Suspension Rear
Independent, Semi trailing arm, Coil Spring, Stabiliser bar.
This vehicles specifications may differ from the above as it may have undergone modification, please check with the seller. The above specifications have been based on manufacturer standard specifications.
^ Repayment examples are based on a Chattel Mortgage commonly used by businesses. Excludes fees and government charges, subject to assessment and approvals. Australian Credit Licence 392426.